• 1/14/12 11:34 am
- 2.7k views • 0 today
- Progress
- 100% complete
- 1
- 0
- 11
8
Hello I havent seen this piston door made before so I thought I would make a tutorial for everyone who, like me, stinks with redstone. By the way I figured this out all by myself.1. Place 2 sticky piston's one right on top of the other. 2. Place 2 sticky pistons on top of eachother 4 blocks away (the fifth block is where you put the pistons)3. Place your favorite blocks right on top of eachother touching the sticky part of the piston do this on both sides. Now put a redstone torch right next to the bottom pistons on the front side only! The bottom pistons should've pushed out now.
4. Go to the side that the torch isnt touching and put a block right to the corner of it and to the top piston. (refer to picture 3 for this if you dont get it.) Do this on both sides!
5. Place redstone from both the torches to the top block. (see picture 3 up the stonebrick)
6. Now the door's should've closed put 2 pressure plates in front of the blocks (door) (see picture 4) Then dig 1 down on both sides directly to the left and right of the pressure plates. Place redstone there.
7. Now you have a working 1 way door Now If you want to make it a 2 way door continue reading.
8. Now repeat step 6 but on the other side. There should be NO redstone torches on this new side.
9. Look where the bottom block That you have redstone running up is (see picture 3) Look at picture seven and do that YOU MUST START NEXT TO THE PRESSURE PLATE on the back side (the side we just started)
10. New color! :) I am going to call the new side "back" and the old side "front" Go to the back side of the door and if you are facing the door walk left until you see the block with redstone that is for the front side. Now dig 3 down directly to the "back" side of it. connect this in the shortest, UNless you run into other redstone, way possible to the redstone directly next to one of the pressureplates on the back side (see picture 4 for what the redstone looks like.
11. Now you need to put redstone throught a tunnel under all of the other redstone until you get to the front side then you need to make is run DIRECTLY into the block that the redstone torch (the one on the same side as the pressureplate that you started at) if done correctly you should have a door that open's onely one side from both front and back. (see picture 8 for redstone wiring)
12. Do the same with the other side but going to the other torch.
13. If this worked correctly you will have a fairly small fully functional piston door!]
If you need help comment and ask!
Please diamond and comment if it worked or not!
4. Go to the side that the torch isnt touching and put a block right to the corner of it and to the top piston. (refer to picture 3 for this if you dont get it.) Do this on both sides!
5. Place redstone from both the torches to the top block. (see picture 3 up the stonebrick)
6. Now the door's should've closed put 2 pressure plates in front of the blocks (door) (see picture 4) Then dig 1 down on both sides directly to the left and right of the pressure plates. Place redstone there.
7. Now you have a working 1 way door Now If you want to make it a 2 way door continue reading.
8. Now repeat step 6 but on the other side. There should be NO redstone torches on this new side.
9. Look where the bottom block That you have redstone running up is (see picture 3) Look at picture seven and do that YOU MUST START NEXT TO THE PRESSURE PLATE on the back side (the side we just started)
10. New color! :) I am going to call the new side "back" and the old side "front" Go to the back side of the door and if you are facing the door walk left until you see the block with redstone that is for the front side. Now dig 3 down directly to the "back" side of it. connect this in the shortest, UNless you run into other redstone, way possible to the redstone directly next to one of the pressureplates on the back side (see picture 4 for what the redstone looks like.
11. Now you need to put redstone throught a tunnel under all of the other redstone until you get to the front side then you need to make is run DIRECTLY into the block that the redstone torch (the one on the same side as the pressureplate that you started at) if done correctly you should have a door that open's onely one side from both front and back. (see picture 8 for redstone wiring)
12. Do the same with the other side but going to the other torch.
13. If this worked correctly you will have a fairly small fully functional piston door!]
If you need help comment and ask!
Please diamond and comment if it worked or not!
Additional Notes
More like this
![[EASY] Piston Door [TUTORIAL] Minecraft Map & Project](https://static.planetminecraft.com/files/resource_media/screenshot/1201/Picture01_4533128_thumb.jpg)
[[Enderkul]]
ho123
SammyKnucklez
forgacs10
485491
2
Have something to say?
when you do pictures you cant see where what u just placed should be
%%%%@ You cant go @%
......................................%
......................................%
And I am sorry if it is confusing I am not very goodat explaining
http://imageshack.us/g/17/20120114175925.png/
+
http://img849.imageshack.us/img849/8462/20120114180424.png